Thermon TraceNet TCM 18 Manual do Utilizador Página 38
- Página / 96
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
The ON/OFF mode may be used with either mechan-
ical relay or solid state relay heater current switching
relays. The SOFT START and PROPORTIONAL con-
trol methods are only used with the zero crossing solid
state current switching relay configurations as these
control modes pulse power during start-up, power
clamping, and also when employing a full proportional
control algorithm.
Press the PROG key at any point to exit from this se-
quence. If left in the program mode, the TCM18 will af-
ter a short wait automatically return to the scan mode.
PROG plus
HEATER
CURRENT
This display screen allows the programming of the
default power clamp percentage in the event of an RTD
fault for each of the eighteen circuits individually or
for all circuits (in the case the value is identical). The
setting range limits for this parameter is 20 to 100%.
Noting the location of the flashing cursor, press the UP
or DOWN keys to change the present settings. Press
the ENTER key to accept the new values.
Press the PROG key at any point to exit from this se-
quence. If left in the program mode, the TCM18 will af-
ter a short wait automatically return to the SCAN mode.
PROG plus
GROUND
CURRENT
1
This display screen allows the programming of the
ground/earth leakage current value at which to trigger
an alarm or trip event for each of the eighteen circuits
individually or for all circuits (in the case the value is
identical). The setting range limits for this parameter is
15 to 225 mA.
Press the PROG key at any point to exit for this se-
quence. If left in the program mode, the TCM18 will af-
ter a short wait automatically return to the SCAN mode.
PN 50316_0514 34
- TraceNet™ TC 1
- Series Control System 1
- Maintenance Guide 2
- Contents 3
- 1 Introduction 5
- PN 50316_0514 2 6
- 2 Specifications 7
- 5 PN 50316_0514 9
- 3 Module Connections 11
- PN 50316_0514 8 12
- The RTB6 Module Connections 13
- The PM6 Connections 14
- The RM6 Connections 15
- 4 Field and Panel Wiring 16
- 13 PN 50316_0514 17
- Figure 6: RTD Sensor Location 17
- TraceNet Panel Wiring 18
- Serial Communication Wiring 18
- PN 50316_0514 19
- 5 Monitoring Heat 20
- 17 PN 50316_0514 21
- PN 50316_0514 18 22
- 19 PN 50316_0514 23
- PN 50316_0514 20 24
- 21 PN 50316_0514 25
- 6 Accessing Heat Tracing 26
- Figure 12: TCM18 LCD Response 27
- 23 PN 50316_0514 27
- PN 50316_0514 24 28
- 25 PN 50316_0514 29
- (1, 2, 3, 4, 5) 30
- PN 50316_0514 26 30
- 7 Programming the 31
- PROGRAM MODE ENABLED 32
- SELECT FUNCTION KEY 32
- Press the MAINTAIN TEMP key 32
- Figure 15: MAINTAIN TEMP Key 33
- 29 PN 50316_0514 33
- Figure 17: Programming Keys 34
- Figure 19: The ENTER Key 35
- 31 PN 50316_0514 35
- Figure 21: The PROG Key 36
- 33 PN 50316_0514 37
- PN 50316_0514 34 38
- 35 PN 50316_0514 39
- PN 50316_0514 36 40
- 37 PN 50316_0514 41
- PN 50316_0514 38 42
- 39 PN 50316_0514 43
- PN 50316_0514 40 44
- 41 PN 50316_0514 45
- PN 50316_0514 42 46
- 43 PN 50316_0514 47
- PN 50316_0514 44 48
- 45 PN 50316_0514 49
- 8 Heat Trace Control and 50
- 47 PN 50316_0514 51
- 9 The TCM18 in 52
- Figure 24: Heater Setup 53
- 49 PN 50316_0514 53
- Figure 25: Select RTD Setup 54
- 10 The TCM18 in 55
- PN 50316_0514 52 56
- 11 The TCM18 Data 57
- 12 System Start-Up 58
- 13 Maintenance 59
- PN 50316_0514 56 60
- 57 PN 50316_0514 61
- Wiring and Connections Survey 62
- 59 PN 50316_0514 63
- 14 Notes 64
- 61 PN 50316_0514 65
- 15 More Information 66
- Appendix A 67
- Trouble Shooting Tips 67
- PN 50316_0514 64 68
- Low Temperature Reading/Alarm 69
- PN 50316_0514 66 70
- 67 PN 50316_0514 71
- RTD Sensor Alarm 72
- Communications Alarm 72
- Circuit Fault Alarm 73
- High Current Readings/Alarms 73
- PN 50316_0514 70 74
- Low Current Readings/Alarms 75
- PN 50316_0514 72 76
- High Ground Current Alarm 77
- PN 50316_0514 74 78
- Appendix B Temperature and 79
- Current Limits 79
- PN 50316_0514 76 80
- Appendix C 81
- Advanced Features of the 81
- TCM18 Ambient Control 81
- PN 50316_0514 78 82
- 79 PN 50316_0514 83
- Appendix D Typical TCM18 84
- Control Applications 84
- 81 PN 50316_0514 85
- 83 PN 50316_0514 87
- 85 PN 50316_0514 89
- PIPE TEMPERATURE 90
- DEGREES CELSIUS 90
- 87 PN 50316_0514 91
- 89 PN 50316_0514 93
- Appendix E Utilities 94
- Appendix F Markings for 95
- Explosive Atmospheres) 95
- Thermon Manufacturing Company 96
- 100 Thermon Drive 96
- San Marcos Texas 96
- Thermon PN 50316_0514 96
Manuais e produtos relacionados com Hardware Thermon TraceNet TCM 18
Hardware Thermon HeetSheet Manual do Utilizador
(4 páginas)
(4 páginas)
Hardware Thermon ET-6C Manual do Utilizador
(2 páginas)
(2 páginas)
Hardware Thermon FAK-4L Kit Manual do Utilizador
(5 páginas)
(5 páginas)
Hardware Thermon TBX-3LC Manual do Utilizador
(5 páginas)
(5 páginas)
Hardware Thermon ET-7C Manual do Utilizador
(4 páginas)
(4 páginas)
Hardware Thermon FAK10A-B-C Manual do Utilizador
(4 páginas)
(4 páginas)
Hardware Thermon FAK-7 Manual do Utilizador
(2 páginas)
(2 páginas)
Hardware Thermon FAK-9 Manual do Utilizador
(4 páginas)
(4 páginas)
Hardware Thermon FAK-1 Manual do Utilizador
(4 páginas)
(4 páginas)
Hardware Thermon FAK-2 Manual do Utilizador
(4 páginas)
(4 páginas)
Hardware Thermon FAK-4 Manual do Utilizador
(4 páginas)
(4 páginas)
Hardware Thermon FAK-5 Manual do Utilizador
(4 páginas)
(4 páginas)
Hardware Thermon FAK-8 Manual do Utilizador
(4 páginas)
(4 páginas)
Hardware Thermon KSR Manual do Utilizador
(7 páginas)
(7 páginas)
Hardware Thermon KSR-EJK Manual do Utilizador
(3 páginas)
(3 páginas)
Hardware Thermon KSR-CFK Manual do Utilizador
(5 páginas)
(5 páginas)
Equip USB-Kabel Benutzerhandbücher
Beginnend mit 0-9
Comentários a estes Manuais